FEOA Forums banner

sway bar fell off

1418 Views 11 Replies 6 Participants Last post by  steve95trc
It´s still attached to the crossmember, but the bolts on both sides where it attaches on the far ends fell off, so it´s just hangin kinda limp.

Should I just buy new bolts and screw it back together?
1 - 12 of 12 Posts
hmmmm....I would say yes d3f reattach it...while you´re at it why not put in some urethane bushiungs....?
Damn dude, what ISN´T rusted off on that car??? First your resenator now this. Hey Everyone, I sugest you all start buying stock in duct tape, because as long as this car is on the road there will be a huge market for the sticky grey repair man.
<TABLE BORDER=0 ALIGN=CENTER WIDTH=85%>[TR][TD]Quote:

[/TD][/TR][TR][TD]
16-03-2003 at 04:31, Pimp_scort_89_GT wrote:
Damn dude, what ISN´T rusted off on that car???
[/TD][/TR][TR][TD]

[/TD][/TR][/TABLE]

Lol....

well, you know how the sway bar is like a kinda "U shaped" bar, right? the base of the U is attached to the crossmember and then the tips of the u are basically hanging off... sigh. I guess it´s almost funny. Wait... no it isnt. :)

Also, my reverse light backup switch isn´t working. Get this-

Before, my reverse lights rarely worked. There´s apparently something in the tranny which engages the switch, and because of wear and tear, it rarely hits the switch and works right, even though the switch is fine.

I need to pass inspection, so the shop replaces the switch and then tests the car and it HAPPENS to work. (It happens about once every 20 tries)

And those damn switches cost 73 bucks too.

Yeah I´m over 300 bucks in the hole.
See less See more
But you own a GT now and thats all that matters. Right??
haha... my LX is in much much better condition, but still nowhere near as quick and tight handling as my GT. I´m glad I bought it, and I was expecting this, but I wasn´t really counting on spending 290 bucks to get my o2 sensor removed (morons).

Well I´m doing only my own work from now on, end of story, period.
Well I had to Finally hit 500, so I thought I´d waste another post here and tell everyone about the bumper sticker I saw for your car...

"Honk if parts fall off"

And then the sticker I´m gunna make for my car...

"WARNING: This car is it´s own theft deterant system"
<TABLE BORDER=0 ALIGN=CENTER WIDTH=85%>[TR][TD]Quote:

[/TD][/TR][TR][TD]
16-03-2003 at 08:30, Pimp_scort_89_GT wrote:
And then the sticker I´m gunna make for my car...

"WARNING: This car is it´s own theft deterant system"
[/TD][/TR][TR][TD]

[/TD][/TR][/TABLE]

AHAHAHAHHA!!!! PATEND PENDING!! PATEND PENDING!!

*note: i assume the position of making that my msn name, and have diplomatic emunity towards anyone who may or has already taken ownership for it*
Anyone know if I can take a Sway bar off a GT and put it on my LX? I have a 1995 LX 2 Dr HB.
zzyzzx yes you can, but better yet get one off a wagon its the beefiest of the stock sway bars.

Steve
steve-

you serious? I´ve got a 95LX wagon. Maybe I´ll swap it wid my 91GT. thx for the heads up.
<TABLE BORDER=0 ALIGN=CENTER WIDTH=85%>[TR][TD]Quote:

[/TD][/TR][TR][TD]
10-04-2003 at 23:59, siragan wrote:
steve-

you serious? I´ve got a 95LX wagon. Maybe I´ll swap it wid my 91GT. thx for the heads up.
[/TD][/TR][TR][TD]

[/TD][/TR][/TABLE]

YEP serious. Check it out.

Steve
1 - 12 of 12 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top